Chip Tuning Tools - Page 7


Page 7 of 7 FirstFirst ... 567
Results 121 to 134 of 134

Thread: Chip Tuning Tools

  1. #121
    Senior Member Stage 2 ECU
    Join Date
    Nov 2020
    Location
    Estonia, Tallinn Harju maakond, Kesklinna linnaosa, Narva mnt 7-634
    Posts
    134

    Default

    ❗️ Autotuner Update for Bosch ME17.9.52! ❗️

    ➡️ Bench reading and writing for Bosch ME17.9.52 on Peugeot and Toyota in Autotuner

    Autotuner is now able to perform the following operations:

    ✅ Bench Reading
    ✅ Bench Writing

    On the following ECU:

    ✅ Bosch ME17.9.52

    Vehicles concerned:

    ✅ Peugeot 1.0i 69hp
    ✅ Toyota 1.0i 69hp
    ✅ Toyota 1.0 VVT-i 69hp

    Autotuner Master
    Autotuner Slave
    ☑️ WhatsApp: +7 (921) 539-93-54

  2. #122
    Senior Member Stage 2 ECU
    Join Date
    Nov 2020
    Location
    Estonia, Tallinn Harju maakond, Kesklinna linnaosa, Narva mnt 7-634
    Posts
    134

    Default

    ❗️ KESSv2 Update: Agriculture Vehicles ❗️

    ✅ KESSv2 allows you to read and write agriculture vehicles via OBD such as Case Ih, New Holland and Steyr, supporting Bosch MD1CE101 ECUs. More than 700 new vehicles available!

    ➡️ More information here

    KESSv2 Master
    KESSv2 Slave
    ☑️ WhatsApp: +7 (921) 539-93-54

  3. #123
    Senior Member Stage 2 ECU
    Join Date
    Nov 2020
    Location
    Estonia, Tallinn Harju maakond, Kesklinna linnaosa, Narva mnt 7-634
    Posts
    134

    Default

    ❗️ M&D Flasher Pre-Order Licenses! ❗️

    ✅ License 84- GM Bosch BCM BENCH and Continental BCM BENCH and License 86 - GM ECU Sirius D3/D32/4R/42R/D42/D52 are up for pre-order!

    ➡️ More information here

    License 86
    License 84

    The activation files will be sent within a week after 22.02.2022
    ☑️ WhatsApp: +7 (921) 539-93-54

  4. #124
    Senior Member Stage 2 ECU
    Join Date
    Nov 2020
    Location
    Estonia, Tallinn Harju maakond, Kesklinna linnaosa, Narva mnt 7-634
    Posts
    134

    Default

    ❗️ Two brand new tools: MUT-3 J2534 Driver and Mitsubishi Flasher! ❗️

    MUT-3 J2534 Full Driver works with the original software for Mitsubishi MUT3 diagnostics. The driver supports 100% functionality of the original MUT III and MUT III Lite Scanner.

    Mitsubishi Flasher is a Mitsubishi ECU programmer for chip tuning and car repairing. The USB dongle is required for working. Reading and writing control units is done via the J2534 adapter.

    ➡️ More information here
    ☑️ WhatsApp: +7 (921) 539-93-54

  5. #125
    Senior Member Stage 2 ECU
    Join Date
    Nov 2020
    Location
    Estonia, Tallinn Harju maakond, Kesklinna linnaosa, Narva mnt 7-634
    Posts
    134

    Default

    ❗️ FLEX version 6. 4.0.0 released! ❗️

    ➡️ New Bench Solutions for Bosch SPC58 Control Units in FLEX

    Here are some of the supported vehicles:

    ✅ Suzuki 1.4T BoosterJet 48v 2021
    ✅ Peugeot 1.2 VTI Puretech 2021
    ✅ Opel Mokka 1.2 Turbo 2021
    ✅ Mahindra 2.2 CRDe 2020

    The new bench protocol is available for the following software packages:

    ➡️ FLS0.1 – SW Flex ECU (car, van, bike) OBD + Bench
    ➡️ FLS0.10 – SW Flex Infineon TC17xx / TCxxx
    ➡️ FLS0.5 – FULL Flex

    New protocols added

    ✅ Suzuki BOSCH MG1CS026: Read / Write / Checksum Internal Flash; Read / Write Internal Eeprom; Full backup
    ✅ DS BOSCH MG1CS032: Read / Write / Internal Flash Checksum; Read / Write Internal Eeprom; Full backup
    ✅ Peugeot BOSCH MG1CS032: Read / Write / Checksum Internal Flash; Read / Write Internal Eeprom; Full backup
    ✅ Opel BOSCH MG1CS032: Read / Write / Checksum Internal Flash; Read / Write Internal Eeprom; Full backup
    ✅ Mahindra BOSCH MD1CS018: internal flash read / write / checksum; Read / Write Internal Eeprom; Full backup

    Software Improvements


    ✅ Added support for JLR BOSCH 6HP28 in Bench

    Bug fixes

    ✅ Fixed OBD writing problem for some versions of Porsche AL552
    ✅ Fixed CRC issue with BOSCH EDC16C39 in Bench

    ⭐️ FLEX Master
    ⭐️ FLEX Slave
    ☑️ WhatsApp: +7 (921) 539-93-54

  6. #126
    Senior Member Stage 2 ECU
    Join Date
    Nov 2020
    Location
    Estonia, Tallinn Harju maakond, Kesklinna linnaosa, Narva mnt 7-634
    Posts
    134

    Default

    ⭐️❗️ PCMflash Update! ❗️ ⭐️

    New modules and additions to the current protocols in PCMflash!

    Module 82: Bosch SH725XX TCU Bootloader, designed to work in service mode (on the bench) with Bosch TCUs with SH725xx microcontrollers, available in ZF 8HP, VAG DQ380/381/500, MEG17.9.8, MEG17.9.13, MEG17.9.21, TC60/80. Supports Flash and EEPROM reading, writing, checksum corrections.

    Module 83: VAG Bosch DQ380/DQ381/DQ500/ZF 8HP, designed to work via the diagnostic connector with DSG and automatic transmission units used in VAG vehicles. Reading (virtual), writing, checksum corrections.

    Module 84: VAG Delphi DCM6.2 supports working via the diagnostic connector of VAG vehicles with Delphi DCM6.2 ECUs. Supports virtual reading, writing, checksum corrections.

    Module 85: Ford Gearbox is designed for working via the diagnostic connector with 6HP28, 5R/6R/6 °F/8 °F/10R TCUs of various modifications used in Ford vehicles. Reading, writing and checksum corrections is supported.

    ➡️ Updates for the existing modules can be found here ⬅️
    ☑️ WhatsApp: +7 (921) 539-93-54

  7. #127
    Senior Member Stage 2 ECU
    Join Date
    Nov 2020
    Location
    Estonia, Tallinn Harju maakond, Kesklinna linnaosa, Narva mnt 7-634
    Posts
    134

    Default

    ❗️ New tools in our catalog: DFOX Master and Slave! ❗️

    ⭐️ DFOX from DFB TECHNOLOGY allows serial communication with the Engine and Automatic transmission control units via the OBD diagnostic socket. It is a professional software for reading and programming the control units of:

    ✅ Cars
    ✅ Trucks
    ✅ Motorbikes
    ✅ Tractors
    ✅ Boats
    ✅ Additional TCU package available for Automatic Transmissions

    ➡️ It also allows communication in the following modes:

    ✅ BDM and JTAG
    ✅ BOOT Mode
    ✅ BENCH Mode (or Service mode)
    ✅ FULL SYSTEM via pinout

    ➡️ Compatible operating systems:

    ✅ Windows 7
    ✅ Windows 8/8.1
    ✅ Windows 10
    ✅ Windows 11!

    ➡️ Minimum recommended requirements:
    CPU > 2.5 GHz (Intel i5, i7)
    RAM > 4GB

    The tool has annual subscription, though it is not mandatory for working.

    ECUTools are the first and only dealer of DFB TECHNOLOGY in Russia!

    ➡️ DFOX Master
    ➡️ DFOX Slave
    ☑️ WhatsApp: +7 (921) 539-93-54

  8. #128
    Senior Member Stage 2 ECU
    Join Date
    Nov 2020
    Location
    Estonia, Tallinn Harju maakond, Kesklinna linnaosa, Narva mnt 7-634
    Posts
    134

    Default

    ❗️ M&D flasher license for GM ACDelco E37/E38 is open for pre-order! ❗️

    ✅ PRE-ORDER License 90 — GM ACDelco E37/E38 ECU BENCH/OBDII is up!

    The module works with ACDelco E37/E38 in OBDII Mode or Bench Mode.

    ➡️ 1. OBDII Mode (working in the vehicle):

    ✅ Identification
    ✅ Error reading
    ✅ Error reset
    ✅ Flash reading
    ✅ Calibration area writing (without checksum corrections)

    ➡️ 2. Bench Mode:

    ✅ Flash reading
    ✅ Flash writing (without checksum corrections)
    ✅ EEPROM reading
    ✅ EEPROM writing

    Not all software versions may be supported.

    ⭐️ The activation files will be sent within a week after 03.05.2022
    ☑️ WhatsApp: +7 (921) 539-93-54

  9. #129
    Senior Member Stage 2 ECU
    Join Date
    Nov 2020
    Location
    Estonia, Tallinn Harju maakond, Kesklinna linnaosa, Narva mnt 7-634
    Posts
    134

    Default

    ⭐️❗️ NeoX - a new odometer and editing tool! ❗️⭐️

    NeoX supports VIN editing, mileage and airbag repairing, pincode reading and editing of ECUs.

    NeoX features:

    ✅ Millage repair and VIN Editor with auto CRC Aurix;
    ✅ PSA MD1CS003 — MERCEDES MD1CP001 — RENAULT MD1CS006 — AUDI MD1CP004 — VW MG1CS011;
    ✅ Millage repair with automatic checksum calculation in eeprom SID 208 Citroen Jumper, Peugeot Boxer, Fiat Ducato;
    ✅ Millage repair with automatic checksum calculation in eeprom SIMOS 18.1 VAG groupAuto CRC — eeprom checksum correction Cranchi Zaffiro 36, Caterpillar model C32, Mercury Varado, Volvo Penta D6;
    ✅ ECU DATABASE EEPROM + FLASH;
    ✅ Millage repair with automatic checksum calculation in eeprom DCM6.1 FORD;
    ✅ Millage repair with automatic checksum calculation in eeprom SID310 Mercedes, Renault, Nissan, Dacia;
    ✅ Millage repair with automatic checksum calculation in eeprom DCM3.7 Kia, Hyundai;
    ✅ Programming and editing in EDC17, MED17, MEV17 with CRC;
    ✅ Programming and editing of electronic counters, forklift trucks, tractors, agricultural vehicles and combines, construction machines;
    ✅ Repairing electronic counters (if data in the dashboard is corrupted);
    ✅ Repairing and programming AIRBAG modules;
    ✅ PIN code — reading from car’s ECU (CIM, BSI, UCH, etc.)
    ✅ Programming and editing on motorcycles, scooters, and quads;
    ✅ Reading, programming and changing code in the radio.

    This tool requires tokens and annual subscription to work. Every member gets 30 free tokens every month.

    Program requirements: computer with minimum Windows 7, 64bit.

    ➡️ More information here ⬅️
    ☑️ WhatsApp: +7 (921) 539-93-54

  10. #130
    Senior Member Stage 2 ECU
    Join Date
    Nov 2020
    Location
    Estonia, Tallinn Harju maakond, Kesklinna linnaosa, Narva mnt 7-634
    Posts
    134

    Default

    ❗️ HEXPROG II is now available for purchase! ❗️

    Hexprog II is a programming tool that supports OBD, Bench work and BMW ISN reading. The pinnacle of ECU cloning and chip tuning advancements with a lightning-fast, dependable, and user-friendly software.

    The tool is presented in two sets: Basic and Full, one allows "renting" the tool for 48 hours, the other has a classic annual subscription.

    ➡️ More information here ⬅️
    ☑️ WhatsApp: +7 (921) 539-93-54

  11. #131
    Senior Member Stage 2 ECU
    Join Date
    Nov 2020
    Location
    Estonia, Tallinn Harju maakond, Kesklinna linnaosa, Narva mnt 7-634
    Posts
    134

    Default

    ❗️ New Trasdata Master is in stock! ❗️

    We are happy to present the much anticipated New Trasdata Master

    New Trasdata is a unique tool supporting all microprocessors utilized by any kind of vehicles in the Automotive field, for reading and programming operations in JTAG, BDM and BOOT mode.

    ➡️ Information about the tool can be found here ⬅️
    Last edited by ECUtools; 07-26-2023 at 01:27 PM.
    ☑️ WhatsApp: +7 (921) 539-93-54

  12. #132
    Senior Member Stage 2 ECU
    Join Date
    Nov 2020
    Location
    Estonia, Tallinn Harju maakond, Kesklinna linnaosa, Narva mnt 7-634
    Posts
    134

    Default

    ❗️ DaVinci Deluxe Edition is open for ordering ❗️

    DaVinci Deluxe is an online working editing software that corrects the errors related with the modern antipollution systems.

    ➡️ Click for more information ⬅️
    ☑️ WhatsApp: +7 (921) 539-93-54

  13. #133
    Senior Member Stage 2 ECU
    Join Date
    Nov 2020
    Location
    Estonia, Tallinn Harju maakond, Kesklinna linnaosa, Narva mnt 7-634
    Posts
    134

    Default

    ❗️ ECUDecoder has been added to our catalog ❗️

    ECUDecoder was developed for disabling of Adblue, DPF, EGR, DTC, Hotststart, Lambda, Speedlimit, Flap, Nox, O2, TorqMonitoring, Start-Stop, duckduckduckduck, TProt and more.

    ➡️ More information ⬅️
    ☑️ WhatsApp: +7 (921) 539-93-54

  14. #134
    Senior Member Stage 2 ECU
    Join Date
    Nov 2020
    Location
    Estonia, Tallinn Harju maakond, Kesklinna linnaosa, Narva mnt 7-634
    Posts
    134

    Default

    ❗️ SwifTec is open for ordering ❗️

    ✅ SwifTec is available in Basic, Standard and Full pack!

    Swiftec Software allows the end user to get the maximum control of modern combustion, electric and hybrid engines, transmissions and battery electronic modules and its subsystems used in vehicles such as cars, trucks, motorbikes, tractors or boats to accomplish different special or daily vehicles aftermarket service tasks!

    ➡️ More information is presented here ⬅️
    ☑️ WhatsApp: +7 (921) 539-93-54

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •